will
Q: Can it use for outdoor lighting? Any effects of sunlight on el light?
Asked by Ghanshyam on 2019-10-12 05:47:01
will Ihave mine mounted on the ceiling and got it working fine. Most software supports mirroring and flipping of the image at output time - including the app they suggest.
2021-05-06 08:12:44 Helpful (0)Q: what temp Sensor is in the Hotend?
Asked by Kai on 2020-12-21 04:25:55
will Itis an NTC 100K thermistor - the same type that is in the Ender 3 by default. I made a 1:1 switch on my machine rather than put this whole hotend my machine. The milling around the thermistor seemed way too large and would need a thermal compound to conduct to the block well. Thermistor and heater cartridge worked just fine though.
2021-05-06 08:10:19 Helpful (0)Q: Is it suitable to be used for a DIY 3d printer?
Asked by R0203 on 2021-01-13 10:12:08
will This board is suitable for DIY printer so long as your build will not exceed 15A total draw going through this board. The traces in the board are rated just above the 15A mark.
2021-01-13 10:17:48 Helpful (0)Q: What type of connector is it?
Asked by BG411447443 on 2020-12-17 10:20:21
will It depends what connectors your referring to - there are a number of them. For power it's screw terminals. For steppers it's dupont inputs, for steppers it's JST connectors. There are other connectors too depending on what your looking to attach.
2020-12-17 02:04:55 Helpful (0)Q: Does this module provide constant current for driving high power LEDs?
Asked by Profic245 on 2020-11-15 03:28:47
will I never measured it with an oscilloscope or anything like that but I've used these for basic led strip lights drawing 3A at 5v bucked from 12v and I also boosted 5v to 12v at 2A. There was no voltage dips at that point (there is an alright smoothing capacitor on the output). I wouldn't push the much farther than that to power high drain LEDs because they got very hot how I used them. Youd want a heatsink on the regulator or maybe even a fan. At that point your better off just using a more well suited power supply I reckon.
2020-11-15 03:48:40 Helpful (1)Q: is this duel extruder wil fit to my lotmaxx shark 3d?
Asked by BG191854320 on 2020-10-19 01:52:31
will Notsure about this, if it has the same mounting holes as an Ender 3 and you can adjust the position on your z limiter to account for it possible different size then should fit.
2020-10-20 01:03:26 Helpful (1)Q: Can you see IR light at night?
Asked by mihakrsevan on 2020-10-20 12:55:01
will You can, the camera includes IR leds to iluminate what it's looking at as well and switches to IR mode when it is in low light. I have not tested the distance it can cover as I use these inside a small hallway and small room.
2020-10-20 12:59:27 Helpful (1)Q: How high can this unit go? 150C? 300C? 999C? Or is the software going to stop at 110C??
Asked by rcooke1963 on 2020-06-30 08:42:55
will I have measured as high as 102c in boiling water just to test if it could handle it and and it seemed stable. What I would say though is that the wire covering seems more like plastic than rubber. It wouldn't stand such high temperatures for long at all (and indeed the test I done in boiling water the cable wrap already seemed to get damaged). The actual probe thermisor is completely sealed though and is absolutely fine.
2020-06-30 09:39:08 Helpful (1)
Q: Can you view the live feed on Amazon Echo Show?
Asked by sajal_mitra on 2020-01-25 07:16:35
will Icould not get integration working with Echo Snow or a Google Home Screen. There is options in the app to configure it but the instructions do not work for me. I send this through to Home Assistant instead.
2020-06-02 10:03:36 Helpful (1)
will There is no auto tracking, you have to manually move it via the app (and FYI moving it has a noticable servo motor noise - in a quiet hallway or even a moderately noisy room it is noticable).
2020-06-02 09:09:32 Helpful (1)Q: quantas placa vem e quais seus tamanhos?
Asked by BG104781537 on 2020-05-20 06:54:17
will Existem10 de cada tamanho. 4 tamanhos diferentes. - 50 x 70 mm, - 40 x 60 mm, - 30 x 70 mm, - 20 x 80mm
2020-05-22 11:50:51 Helpful (1)Q: what is the thickness dimension?
Asked by brick66 on 2020-05-13 06:22:29
will Minewere about 10mm thick
2020-05-22 11:47:47 Helpful (4)Q: is this complete set or without power supply?
Asked by christiandknights on 2020-04-27 12:13:44
will Mine did not have a power supply. It requires a 12v (suggest more than 2Amp) supply. Accepts a barrel jack style input.
2020-04-27 04:48:45 Helpful (2)Q: somebody upgrade Y dimension? please give me info about it
Asked by Danil45 on 2020-04-11 10:09:22
will Thestock Y dimensions in the firmware are 220mm. The actual buildplate is more like 235mm though but there's a little edge that it won't print in unless you adjust or change firmwares.
2020-04-13 03:03:44 Helpful (1)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
will Ihad the purple one of these I bought outside and it was barely visible in daylight. I don't think it was anything to do with it being sunlight - they are just not super bright.
2021-05-06 08:13:48 Helpful (0)