mike_fpv
grabejud it should turn off when tx is off. i should turn off also if the external tx is not use. there is something wrong with your connection and wiring.
2022-01-24 01:54:01 Helpful (1)Q: This item hasn’t been in stock for over a year. When will it be in stock ?
Asked by mike_fpv on 2021-11-18 06:11:23
Denouement not sure yet.
2021-11-30 08:29:04 Helpful (0)
Stipo Hi, I've only had one so far. It worked perfectly. After one fall I lost two resistors and somehow regained them. It still works but with interference. I recently ordered another but haven’t installed it yet. So my experience is that I only had one 4 years and it still works ...
2021-11-01 05:17:19 Helpful (1)Q: is the 1250kv motor suitable for 6s, if so what esc is recommend?
Asked by mike on 2019-04-09 11:13:23
BurnNotice1 No
2021-04-17 10:23:40 Helpful (0)Q: Does this camera come with a built in OSD that shows voltage?
Asked by mike on 2018-12-23 02:30:10
Blabla1234 yes it has
2021-05-25 01:49:35 Helpful (0)Q: is this compatible with the Jumper T-Lite 4in one directly or does it need an external module ?
Asked by mike_fpv on 2021-02-04 03:14:27
Richi No, it is not compatible, you need a external Modul with 900Mhz.
2021-02-04 02:14:48 Helpful (0)Q: is this item still in sell status?
Asked by mike_fpv on 2021-01-26 11:55:30
Lolboat yes, but out of stock.
2021-02-04 03:50:04 Helpful (0)Q: what's is the recomended prop for 4s battery?
Asked by bigcarlos on 2019-07-02 01:07:18
mike_fpv I use a 7x7 and it is great. 7x6 also works well on 4s.
2020-11-25 09:47:54 Helpful (0)Q: what esc is recommended for the motor ?
Asked by mike on 2019-06-21 06:11:01
Warbirdman I used a UMX receiver that has two linear servos on the same board along with the correct plug for this particular motor.
2019-08-16 06:36:12 Helpful (0)Q: How do I connect the two wires from the motor to the esc ?
Asked by mike on 2019-07-08 02:20:02
MJMAR04 This is a brushless esc and will require a brushless motor which has three wires. If your motor has two wires, then it is not a brushless motor, it is a brushed motor and needs a brushed esc. They are not cross compatible. But if you did get a brushless motor, you would need to connect the wires by soldering them directly to the board. There are many videos on the internet about this that would help you.
2019-07-13 12:05:44 Helpful (0)
mike I just received my esc, how do I connect the 3 pin connector to the battery to the battery which only has two wires ? please help, I’m very confused. thanks Mike
We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
Den92 Seems like an issue on transmitting side, check you camera and VTX connection.
2021-10-31 04:39:49 Helpful (2)