strassern
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

strassern 28/03/2018
These motors go! I have not had any issues with these motors.
BrotherHobby Returner R4 2205 2450KV 2700KV 4-5S Brushless Motor For RC Drone FPV Racing Multi Rotor
US$24.56 US$31.99
0
Recommendations
Comments (0)
strassern 28/03/2018
This is a 4 in 1 ESC solution that when combo'd with the Stack X F4 Flight Controller provide a very simple installation with less weight than many builds. Only 12 motor wires and a pos/neg battery connection make this board very simple to use for novice/entry level pilots.
Eachine Stack-X F4 Flytower Spare Part 35A 4 In 1 ESC 2-6S BLHeli_S Dshot600 Ready For RC Drone FPV Racing
US$39.70 US$50.99
7
Recommendations
Comments (0)
strassern 28/03/2018
This VTX antenna is designed for shorter visual transmission range but at the balance of much less weight than other more powerful antennas. It does what is expected of it and in the right conditions can go quite far. Nice and affordable. Happy Flying!
Emax F4 Magnum Tower Parts 5.8G Dipole Whip Antenna
US$6.47 US$13.99
0
Recommendations
Comments (0)
strassern 28/03/2018
Very simple installation when paired with Stack-X 4 in 1 ESC unit and right now a lower cost than many other combination boards that include ESCs, FC, and VTX in one combo unit. The final result is only 2 36x36 boards and a reciever for a complete build of the "brains". This means less total soldering (and less weight) and could be helpful to entry level builders who have not perfected their soldering skills yet. There are some sets of pads that need to be addressed called bridges that activate particular settings such as how much voltage sent to the fpv camera and an sbus or ibus(etc used for you transmitter type) bridge. In my case the camera bridge is pre-soldered for 5v but the Sbus bridge needed to be addressed. Ensure you are using the correct amount of heat on your iron to ensure you do not accidentally remove the very small and delicate soldering pads. I would recommend 315-350 degrees Fahrenheit to address these bridges and if you are completely unfamiliar with soldering, please watch some videos and do some research to up your game before handling these bridges specifically. I know you want to get airborne but.....My best advice is DO NOT RUSH your build! As you hone your soldering skills, do your research, ask questions in forums if you need guidance, and don't be in too much of a hurry to get in the sky or you could make a mistake that will ensure you wait for 15-30 days to correct while new hardware ships. Happy Flying!
Eachine Stack-X F4 Flytower Spare Part F4 Flight Controller Integrated OSD 40CH VTX For FPV Racing RC Drone
US$35.06 US$31.59
4
Recommendations
Comments (1)
strassern 28/03/2018
The product arrived as a nice bright yellow color as the picture depicts. I have ordered other versions from other vendors in bulk and they were a light orange/yellow mix dull color. Happy Flying!
XT60 Male Female Bullet Connector Plug For Lipo Battery RC Drone FPV Racing Multi Rotor
US$5.99 US$7.99
0
Recommendations
Comments (0)
strassern 28/03/2018
My only gripe is the exterior form factor. Of course, I assume there are a great deal of differences between different motor mounts and that was taken into account in my review. I personally used these with BrotherHobby Returner R4 2205 2450KV 2700KV motors. The exterior bulges up from the frame by a decent amount as the exterior flange pushes upward from the pressure. I did not like the look of so much material sticking up from the base of the motor. I have not enough experience to speak in relation to the reduction in noise but took the precautions of soft mounting motors and FC/stack. Ultimately this is a mostly unnoticeable unless taking stringent look at the quad up close. Happy Flying!
4 PCS 22XX Series Motor Silicone Anti-vibration Pad in for RC Drone FPV Racing Drone
US$2.70 US$8.99
0
Recommendations
Comments (0)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe