Gonzo78
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

Gonzo78 30/07/2019
The orginal mlvss, works as intended. Quality like every original frsky product. Works with cleanflight/ betaflight together at the smartport. Show up to 6 cell voltages. Do not connect ground to the receiver, if you connect the balancercable in the wrong direction the short will destroy the receiver. You can slide a 4pole xh port without pins over the balancer socket.
FrSky MLVSS Mini Lipo Voltage Sensor Smart port Enable without OLED Screen
US$21.99 US$32.99
6
Recommendations
Comments (0)
Gonzo78 17/01/2021
Very nice set to build for children, manual is not that great, german maker group has created very good howto for the threecolored version.
Geekcreit® DIY Christmas Tree LED Flash Kit 3D Electronic Learning Kit
US$4.79 US$13.99
0
Recommendations
Comments (0)
Gonzo78 17/01/2021
Works like expected, small lightnings.
Geekcreit® DIY Mini Tesla Coil Module Unassembled 15W DC 15-24V 2A Plasma Speaker Electronic Kit
US$2.99 US$6.54
0
Recommendations
Comments (0)
Gonzo78 17/01/2021
Good quality, works well
Geekcreit® ATmega328P Nano V3 Controller Board Improved Version Module Development Board
US$3.99 US$25.99
0
Recommendations
Comments (0)
Gonzo78 17/01/2021
All ok, works well.
10Pcs Geekcreit® DC 5V 3MM x 10MM WS2812B SMD LED Board Built-in IC-WS2812
US$1.79 US$9.99
0
Recommendations
Comments (0)
Gonzo78 17/01/2021
All ok, it is used at at co2 traffic light, to show air quality.
MH-Z19 MH-Z19B Infrared CO2 Sensor Module Carbon Dioxide Gas Sensor for CO2 Monitor 0-5000ppm MH Z19B NDIR with Pin
US$37.72 US$50.99
0
Recommendations
Comments (0)
Gonzo78 17/01/2021
Good usb connectors. Was able to replace mini usb connector at arduino nano v3 clone with one of this microusb ports. Had to bend the pins a little bit, but no problem.
10pcs Micro USB Type B 5 Pin Female Socket 4 Vertical Legs For Solder Connector
US$3.99 US$4.99
0
Recommendations
Comments (0)
Gonzo78 17/01/2021
Very nice product. Printer is now very silent! Tmc2209 are in use at bigtreetech skr1.4. Diagpin removed to use endstopswitches.
5Pcs BIGTREETECH TMC2209 V1.2 Silent StepSticks Stepper Motor Driver VS TMC2130/TMC5160 for 3D Printer Parts SKR V1.3/mini E3
US$41.46 US$49.99
0
Recommendations
Comments (0)
Gonzo78 17/01/2021
Nice board, works very well, very good upgrade to original anet board at e10. Printer is now very silent with tmc2209 stepper driver.
BIGTREETECH® SKR V1.4/SKR V1.4 Turbo Control Board 32-Bit 3D Printer Mainboard Support TMC2130/TMC2209/TMC2208
US$36.29 US$33.06
0
Recommendations
Comments (0)
Gonzo78 17/01/2021
Display has arrived in time. No bubblewrap, box was squezzed like you can see at pictures. Display is working well. Had to replace the display at my anet e10 after i bricked the first one at the board upgrade at the e10 to bigtreetech skr 1.4 turbo.
Adjustable 12864 Display LCD 3D Printer Controller Adapter For RAMPS 1.4 Reprap
US$13.38 US$21.99
0
Recommendations
Comments (0)
Car Digital Radio Receiver USB DAB RDS Non-screen Display European General
US$38.12 US$44.99

Q: Hello, is there any source for a firmwareupdate? It is not very stable and works not on USB Speaker with U Disk port. Thank you very much. But it is a very nice device. Which version will be deliviered? External antenna or fixed wire antenna? Thank you very much.

Asked by Gonzo78 on 2020-01-09 01:48:59

xiangjinhua External antenna

2020-02-17 06:11:19 Helpful (4)
Submit
Answers (1)
Gonzo78 11/07/2019
Nice made connectors.
10 Pair URUAV XT30U Male Female Bullet Connectors Power Plug with Heat Shrink Tubing for Lipo Batter
US$10.99 US$11.99
0
Recommendations
Comments (0)
Gonzo78 11/07/2019
Good like every dys product
DYS D2826 2826 930KV 1000KV 1400KV 2200KV Brushless Motor
US$15.15 US$13.84
0
Recommendations
Comments (0)
TTSRC BLHeli 35A ESC 2-4S Speed Controller for RC Airplane FPV Racing Multi Rotor
US$7.62

Q: can the ESC configured with blheli suite?

Asked by Gonzo78 on 2018-09-06 09:13:58

Lanny Hello, we have sent your question to the supplier, will get back to you soon.

2018-10-07 08:10:42 Helpful (0)
Submit
Answers (1)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe