gnusmas100
Q: it is compatible with the printer cr-200b?
Asked by BG449346375 on 2022-03-01 05:48:37
Q: comes led, tripod and cell phone holder?
Asked by BG245315441 on 2020-10-25 09:12:41
gnusmas100 Yes depens what combination you choice
2021-09-01 03:48:16 Helpful (0)Q: How i can check drone without battery?
Asked by BG111010474 on 2021-08-31 09:01:48
gnusmas100 You can check your drone in betaflight with the micro usb port under nead. The usb cable got deliverd with the drone.
2021-09-01 03:45:47 Helpful (0)Q: what version has the reciever?
Asked by musa1313 on 2021-04-18 01:51:15
gnusmas100 You Can Pick between xm+ and crossfire But Always If you buy it to update the reciever Before you want to bind
2021-04-28 11:20:53 Helpful (0)Q: what batteries can it hold?
Asked by BG491683818 on 2021-02-15 10:40:53
gnusmas100 I would prefer a lipo 4s between 500-1200mah
2021-02-17 02:11:31 Helpful (2)
gnusmas100 This esc are special for Drone motors kv2200 2400 2500
2021-02-13 05:46:04 Helpful (0)
gnusmas100 The foam is for protecting the lipo because the battery is very explosive. I have them still after 2 years. Lipos Come in different size. What you search is level between size en weight
2021-02-13 05:40:26 Helpful (0)
gnusmas100 Yes and no the module you can update to eu the only thing you need to buy is the eu antenna need to be not 900mhz, eu version is 868mhz
2021-02-13 05:37:17 Helpful (0)Q: will this connect to skyzone cobra x or do I need an adapter?
Asked by BG485514817 on 2021-01-25 06:25:20
gnusmas100 Nop you dont need a adapter for the skyzone cobra. Because it has a female connector en this cable with triple patch ha e male connector
2021-01-25 06:59:11 Helpful (1)
Q: which receivers are compatible with flysky i6 and this flight controller?
Asked by Vojko on 2021-01-15 05:14:19
gnusmas100 I use the r9m and the xm+ i prefer the sbus or ibus.
2021-01-16 05:25:10 Helpful (0)Q: How do i get multishot on the esc if im using inav?
Asked by Yash Macin on 2017-11-10 05:27:32
gnusmas100 Not sure about the i nave it depens on your fc and firmware
2021-01-16 05:24:10 Helpful (0)
We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
gnusmas100 Yes, if you wana make it into en direckt extruder thats a issue but for bowden its oke
2022-03-01 03:15:08 Helpful (0)