Beast Mode Expecting big things from this motor

Beast Mode Expecting big things from this motor

Beast Mode Expecting big things from this motor

I put the 2650kv in my arrma vorteks 6 months ago and i run it multiple times a week. Connected to a blx185 running 3s its an absolute monster. I converted it from a boost mega so you will need to upgrade the diffs and the slipper clutch, i am using the hot racing setup. On belted trenchers its and absolutely perfect setup. Add heavier shock oil and thicker front diff fluid. I am using the factory plastic motor mount with out any problems at all. I added the surpass twin fans because it gets hot and i also run it on the local sand dunes. The only issue i had was water getting in motor and destroying the bearings after a month and i do run it in water, mud and snow so it gets hosed off alot. I cleaned it out, replaced the bearings with nicely sealed ceramic units then filled the other unused mounting holes with set screws and a little loctite. Then sealed the end caps with anaerobic sealant and silicone. Its been 5 months including a dip in the ocean by accident and its great. These are the bearings i got to replace the open style trash bearings they have in them. I hate the BLX185 ESC btw

I put the 2650kv in my arrma vorteks 6 months ago and i run it multiple times a week. Connected to a blx185 running 3s its an absolute monster. I converted it from a boost mega so you will need to upgrade the diffs and the slipper clutch, i am using the hot racing setup. On belted trenchers its and absolutely perfect setup. Add heavier shock oil and thicker front diff fluid. I am using the factory plastic motor mount with out any problems at all. I added the surpass twin fans because it gets hot and i also run it on the local sand dunes. The only issue i had was water getting in motor and destroying the bearings after a month and i do run it in water, mud and snow so it gets hosed off alot. I cleaned it out, replaced the bearings with nicely sealed ceramic units then filled the other unused mounting holes with set screws and a little loctite. Then sealed the end caps with anaerobic sealant and silicone. Its been 5 months including a dip in the ocean by accident and its great. These are the bearings i got to replace the open style trash bearings they have in them. I hate the BLX185 ESC btw

I put the 2650kv in my arrma vorteks 6 months ago and i run it multiple times a week. Connected to a blx185 running 3s its an absolute monster. I converted it from a boost mega so you will need to upgrade the diffs and the slipper clutch, i am using the hot racing setup. On belted trenchers its and absolutely perfect setup. Add heavier shock oil and thicker front diff fluid. I am using the factory plastic motor mount with out any problems at all. I added the surpass twin fans because it gets hot and i also run it on the local sand dunes. The only issue i had was water getting in motor and destroying the bearings after a month and i do run it in water, mud and snow so it gets hosed off alot. I cleaned it out, replaced the bearings with nicely sealed ceramic units then filled the other unused mounting holes with set screws and a little loctite. Then sealed the end caps with anaerobic sealant and silicone. Its been 5 months including a dip in the ocean by accident and its great. These are the bearings i got to replace the open style trash bearings they have in them. I hate the BLX185 ESC btw

super. hope they keep them in stock because they are the best buy value for money

super. spero li mantengano in stock perché sono i best buy rapporto qualità prezzo

super. hope they keep them in stock because they are the best buy value for money

It is great for the money. Motor heats up little quicker, than some more expensive brands. Cables are long enough for arrma 6s lineup.

It is great for the money. Motor heats up little quicker, than some more expensive brands. Cables are long enough for arrma 6s lineup.

It is great for the money. Motor heats up little quicker, than some more expensive brands. Cables are long enough for arrma 6s lineup.

received in couple of days. everything well. bench tested and all is fine. Thanks ✌️✌️

received in couple of days. everything well. bench tested and all is fine. Thanks ✌️✌️

received in couple of days. everything well. bench tested and all is fine. Thanks ✌️✌️

mounted on the typhon arrma, very powerful at a super price

montato sulla typhon arrma, potentissimo ad un prezzo super

mounted on the typhon arrma, very powerful at a super price

it's good...didn't know that the bullet connectors were 6.5 doh so make sure your esc has 6.5 connectors and not 4mm.

it's good...didn't know that the bullet connectors were 6.5 doh so make sure your esc has 6.5 connectors and not 4mm.

it's good...didn't know that the bullet connectors were 6.5 doh so make sure your esc has 6.5 connectors and not 4mm.

Great.

Great.

Great.

i like to have 20 Points

i like to have 20 Points

i like to have 20 Points

Strong motor, on a favourable price

Strong motor, on a favourable price

Strong motor, on a favourable price