Customer Reviews

4.95 out of 5
Write a Review
  • All Reviews (299)
  • Image (53)
  • Video (4)
  • All Star
    • All Star(299)
    • 5 Star(287)
    • 4 Star(9)
    • 3 Star(3)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
  • July-15 2020 00:00:00

    4 weeks shipping! Normal Charger Discharger ,bischen complicated dying. Very soft wire cable. All parts are stuck. Thank you!!! Gladly again!!!!

  • September-01 2020 00:00:00

    It is a good product, but there is a crush on the box. There are many things that are grounded at three points.

  • January-20 2021 00:00:00

    All ok missing prove it

  • November-15 2020 00:00:00

    too long to receive this charger

  • September-06 2020 00:00:00

    All right.

  • September-04 2020 00:00:00


  • August-22 2020 00:00:00

    It is a good product although it is three points grounded.

  • August-11 2016 00:00:00

    My Full Review is in my blog here: My first impression is that the unit is well put together and is similar in form-factor to other units we've seen in the field. However there is a long list of features listed in the manual mainly promising easy of use and security I liked * Price is very affordable, especially for a beginner. * English manual written in good English. * Can be configure to charge HV LIPO * Built in balance board. Keeps things compact. * Automatic selection of LIPO cell count depending on which balance port is being used. * Fine-tuning of many parameters. For example you can control the minimum voltage to discharge a LIPO battery. As well many other parameters. * Ready to use charge cables provided for different kinds of connectors. I didn't like * By Default the volume for the key beeper is too loud for indoor use. One of the first things I did was to mute the key beeper. * Connecting the charger to a 12V battery using the alligator clips will produce a spark. Hopefully the electronics inside the charger will protect the charger from the sudden voltage surge. * Input voltage is limited to a maximum of 18V which means I cannot use a 24V heavy duty power supply I normally use on my other charger. * Selecting one of the 10 memory is a bit cumbersome and error prone. You must change the charger mode to "PROGRAM SELECT/Save Settings" or "PROGRAM SELECT/Load Settings" and then select the memory location you intend to save-to or load-from. A small card will have to kept as a reminder of what is saved on each memory location. Other chargers show battery settings associated with each memory location so you don't have to remember that save location 07 contains the settings to charge a 3S 2100mAh LIPO. * Saving saves a "battery set" which to me means that it will save the settings for charging a LIPO battery a PB battery a NiCD battery... all in one memory location. This is different from other chargers where a saved location is associated with one specific battery.

  • October-22 2017 00:00:00

    It's a really nice charger, I'm using it with LiPOs and gives information on each cell, measures the LiPOs internal resistance, lots of options. Quality sturdy case, the overall feel is nice, the interface is ok, 4 button menu, takes a bit of time to get to some options, but most of the time I only use one option anyway so for day to day it's fine and the fact that it does all the rest really adds to the value. Only two downsides I found so far: 1. One the charger has two possible power inputs, one is a jack with a max of 6 Amps, the second one has two banana leads which again is usefull to plug to a more powerful power source. The problem is that you can't remove the banana leads and if you use the plug I measured and there's voltage on those, so it's really easy to short those banana leads when using the plug. If you use the plug I advise putting some tape over the banana leads. 2. The individual cell readings are nice, but I had a bad battery on delivery from another store and I needed a photo proof of the cells voltage, in my case one of the cells was disconnected, so 0v for that cell, and the charger freaks out, just displays balancing error. Took quite a few tries and had to switch to LiPO monitoring and sometimes you can get the cells reading, but it seems random, most of the times it just freaks out sends you back to the menu without display the cells voltage. The second problem might be solved by a firmware update, the first problem doesn't affect me because I am using the banana leads, but took a star from quality just for the bad design leaving those banana leads hot when using the jack. All in all I'm happy with this purchase.

  • March-06 2017 00:00:00

    Мощности с запасом. Помимо стандартных функций заряда/разряда присутствуют такие как: пенорез, измерение внутреннего сопротивления побаночно, обкатка коллекторных моторов. Вентилятор немного шумноват.


    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • AU$44.90
    • AU$5.78
    • AU$34.97
    • AU$106.49
    • AU$43.45
    • AU$6.12
    • AU$50.70
    • AU$39.50
    • AU$104.03
    • AU$72.42
    • AU$4.33
    • AU$65.84
    • AU$48.83
    • AU$56.62
    • AU$14.91
    • AU$9.21
    • AU$25.05
    • AU$114.45