18/02/2021
A good, powerful charge. It doesn't make much sense to list the pros, they're already clear. Iron for home, desktop use and charging of huge batteries, or parallel charging of piles of small packs. Despite the power, the fan is quite adequate, which is not very irritating and turns off at the first opportunity. The Bluetooth module definitely adds convenience. The Android app is slightly uncomfortable and slightly axed, but still better than running to the workplace each time. OTA firmware update. Very cool, but very long (more than 10 minutes). In order to realize the full potential of the device you need a powerful power supply. Preferably something like 24V/1000W. That's about $70more. Capabilities in the category of AKB symbolic - at the level of charging for $30.
Now that you didn't like it.
Touch buttons uncomfortable. Especially after the wheel on ToolkitRC M6D and similar. It is impossible to navigate the menu quickly and accurately. Either fast and by, or slow and accurate. The logic of governance itself is not evident in all points. For example, why can't you run a single channel like dc power on such a powerful charging and use a second channel in any other mode? Instead, the power on dc power is cut down with a polarity error (also delusional, underdeveloped). For that kind of money, you could have a touch screen. The balancing connectors are first on 8S (which is understandable), and secondly deep-sunk and because of this it is not always visible whether you get into the slot or not. There is no connection port for external temperature sensors (at this power!). And most importantly: the balancing cycle is very fast. It may also be very high-quality, but somehow I doubt it. There was no way to test him for the dead, unbalanced AKB.
In general, it would be a perfect iron if the ISDT P30 had a TOOLKITRC M6D firmware and a control wheel added to its power.
In the photo, the P30 charges 10 4S batteries at 1500-1800 mAh through the JB parallel charging board with a current of 15A (and is not energized).
Хорошая, мощная зарядка. Плюсы перечислять не имеет большого смысла, они и так понятны. Железяка для домашнего, настольного использования и зарядки огромных батарей, либо параллельной зарядки кучи мелких паков. Несмотря на мощность, вполне адекватный вентилятор, который не сильно раздражает и отключается при первой возможности. Bluetooth-модуль однозначно добавляет удобства. Приложение под Android слегка неудобное и слегка топорное, но все равно лучше, чем каждый раз бегать к рабочему месту. OTA обновление прошивки. Очень круто, но очень долго (более 10 минут). Для того,чтобы полностью раскрыть потенциал устройства нужен мощный блок питания. Желательно что-то вроде 24В/1000Вт. Это ещё около $70 к стоимости. Возможности по разряду АКБ символические - на уровне зарядки за $30.
Теперь,что не понравилось.
Сенсорные кнопки неудобные. Особенно после колёсика на ToolkitRC M6D и подобных. Быстро и точно перемещаться по меню невозможно. Либо быстро и мимо, либо медленно и точно. Сама логика управления не во всех моментах очевидна. Например, почему на такой мощной зарядке нельзя запустить один канал, как простой dc power, и при этом использовать второй канал в любом другом режиме? Вместо этого питание по dc power вырубается с ошибкой про полярность (тоже бред, недоработано). За такие деньги могли бы и сенсорный экран поставить. Разъёмы балансировки во-первых на 8S (что понятно), а во-вторых утоплены глубоко и из-за этого не всегда видно, попадаешь ты в слот или нет. Отсутствует порт подключения внешних датчиков температуры (при такой-то мощности!). И самое главное: цикл балансировки очень быстрый. Может быть, он ещё и очень качественный, но почему-то я сомневаюсь. Не было возможности проверить его на убитой разбалансированной АКБ.
В целом, это была бы идеальная железка, если бы к мощности ISDT P30 добавить прошивку TOOLKITRC M6D и колесо управления.
На фото P30 заряжает 10 4S аккумуляторов по 1500-1800 mAh через плату параллельной зарядки JB током 15А (и не напрягается).
A good, powerful charge. It doesn't make much sense to list the pros, they're already clear. Iron for home, desktop use and charging of huge batteries, or parallel charging of piles of small packs. Despite the power, the fan is quite adequate, which is not very irritating and turns off at the first opportunity. The Bluetooth module definitely adds convenience. The Android app is slightly uncomfortable and slightly axed, but still better than running to the workplace each time. OTA firmware update. Very cool, but very long (more than 10 minutes). In order to realize the full potential of the device you need a powerful power supply. Preferably something like 24V/1000W. That's about $70more. Capabilities in the category of AKB symbolic - at the level of charging for $30.
Now that you didn't like it.
Touch buttons uncomfortable. Especially after the wheel on ToolkitRC M6D and similar. It is impossible to navigate the menu quickly and accurately. Either fast and by, or slow and accurate. The logic of governance itself is not evident in all points. For example, why can't you run a single channel like dc power on such a powerful charging and use a second channel in any other mode? Instead, the power on dc power is cut down with a polarity error (also delusional, underdeveloped). For that kind of money, you could have a touch screen. The balancing connectors are first on 8S (which is understandable), and secondly deep-sunk and because of this it is not always visible whether you get into the slot or not. There is no connection port for external temperature sensors (at this power!). And most importantly: the balancing cycle is very fast. It may also be very high-quality, but somehow I doubt it. There was no way to test him for the dead, unbalanced AKB.
In general, it would be a perfect iron if the ISDT P30 had a TOOLKITRC M6D firmware and a control wheel added to its power.
In the photo, the P30 charges 10 4S batteries at 1500-1800 mAh through the JB parallel charging board with a current of 15A (and is not energized).