HugoBiermann
HugoBiermann no. but i killed it on probably the 5th 2s pack.
HugoBiermann You also have to buy the spur, motor mount and pinions separately. If you want to shift between high and low gear, also the shift servo.
2021-10-26 12:32:24 Helpful (0)
Q: i know it will be underpowered but will it be able to work on +/- 40v supply?
Asked by anton1@lantic.net on 2019-01-03 02:56:21
HugoBiermann It might, power will be way down though. You might be better off with a different module.
2021-10-18 06:51:15 Helpful (0)
HugoBiermann 3duim. Werk heel goed in die spot waar ek een install het.
Q: I have ZMT-10 by ZD racing. This part is fit for ZMT-10?
Asked by Taka_02 on 2019-07-31 07:03:58
HugoBiermann Its mod06 pitch. If the other car is the same you should be fine. Mod06 should work fine on 48p, essentially the same thing.
2021-10-07 12:23:21 Helpful (0)
HugoBiermann It will probably be best to bey and test.
2021-10-07 12:19:03 Helpful (0)Q: you use these for 1:12 rc crawlers?
Asked by BG501622953 on 2020-10-27 08:02:02
HugoBiermann They need modification to work ok on a crawler. Springs are a bit too stiff.
2021-10-07 12:17:48 Helpful (0)Q: when is the blue one back in stock again?
Asked by jeroenmpdj on 2020-08-15 04:46:45
HugoBiermann They’re almost out of stock again! Buy Now!
2021-09-29 06:54:46 Helpful (0)
HugoBiermann Its a full proportional radio, yes.
2021-09-18 01:50:21 Helpful (0)Q: will both the pin and hex work in the 144001 version?
Asked by BG124622175 on 2021-09-14 05:37:22
HugoBiermann You can always just use your stock pin and just the new adaptor
2021-09-18 01:49:40 Helpful (0)Q: does this work for xinlehong q901/2/3?
Asked by Amin1987 on 2020-12-08 05:45:37
HugoBiermann Yes, if you also change the esc.
2021-09-11 12:57:01 Helpful (0)Q: Est ce que les amortisseurs sont compatible avec le truggy absima at 2.4 brushed ?
Asked by GrégoryFournier on 2019-06-01 11:45:04
HugoBiermann They are 100mm long end for m3 hardware. Stiff enough for general 110 basher or trail rigs. You should decide.
2021-09-11 12:56:23 Helpful (0)
HugoBiermann Make an adaptor or solder one in the place of the deans
2021-09-09 01:45:25 Helpful (0)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
dyavdyaw пришли с адаптерами
2022-03-01 08:41:37 Helpful (0)