p1xninja
My Contents
All Messages
Reviews
Comments
Answers
Questions

Comments

p1xninja Thankyou! Very helpful information!

gNorm 23/05/2022
These boards are amazing. WIth LoRa, BlueTooth, Wi-Fi and GPS they have four radios on a tiny board! Using the Meshtastic project is not quite as turnkey as it could be, and requires some willingness to keep trying to get started. There is a forum on discourse and the devs are active and helpful. Tip: The unit comes with Meshtastic 1.0.0 and needs to be flashed to the current version. The USB driver
LILYGO® TTGO Meshtastic T-Beam V1.1 ESP32 433/915/923Mhz WiFi Bluetooth ESP32 GPS NEO-6M SMA 18650 Battery Holder With OLED
LILYGO® TTGO Meshtastic T-Beam V1.1 ESP32 433/915/923Mhz WiFi Bluetooth ESP32 GPS NEO-6M SMA 18650 Battery Holder With OLED
US$32.99 US$53.99
3
Comments (1)

p1xninja amazing!

Dude 15/07/2019
nice wheels for my 3d printed car project.
4PCS Alloy Rims Tires RC Car Wheels 1/18 WLtoys A959-B A979-B A959 A969 A979 K929 Vehicles Model Parts
4PCS Alloy Rims Tires RC Car Wheels 1/18 WLtoys A959-B A979-B A959 A969 A979 K929 Vehicles Model Parts
US$14.70 US$27.99
1
Comments (1)

p1xninja Absolutly,was my first thought also when I saw this! I have electric matches/fuses for fireworks, would be awesome to launch some fireworks next New Years eve from one of my bigger drones!

nibmit 28/01/2017
There are totally going to be rocket launchers on my quad. Alternates between lines when signal goes high and stays of for about 3 seconds.
Colorful Fireworks Smoke Igniter Iignition Switch Module for RC Models
Colorful Fireworks Smoke Igniter Iignition Switch Module for RC Models
US$8.79 US$9.59
1
Comments (1)

p1xninja @ How do you wire the Current sensor then? have the same FC and I too find it hard to figure out, would have been easier with seperate ESCs but this is otherwise a much better solution. Nice build btw!

runordie 26/03/2019
Great quality/price ratio. No issue so far with this build. Solder pads were well sized. Good product.
30.5x30.5mm Racerstar REV35 35A BLheli_S 3-6S 4In1 Brushless ESC Built-in Current Sensor Support DShot600 for RC Drone FPV Racing
30.5x30.5mm Racerstar REV35 35A BLheli_S 3-6S 4In1 Brushless ESC Built-in Current Sensor Support DShot600 for RC Drone FPV Racing
US$35.99 US$37.99
11
Comments (9)

p1xninja hi! What is that camera that you are using?

akula98 02/03/2017
Quality is ok, nothing to complain at this price point. It uses an older version of Basecam control board, which can only work with version 2.2b of SimpleBGC_GUI. Download it from Basecam Electronics web site, the version here is not compatible. Everything works fine after you calibrate it.
2 Axis Brushless Action Camera Gimbal with Controller Support Remote Control for GoPro 3 FPV Racing RC Drone
2 Axis Brushless Action Camera Gimbal with Controller Support Remote Control for GoPro 3 FPV Racing RC Drone
US$36.64 US$51.59
5
Comments (3)

p1xninja Goodthing to mention about the M5 screw, luckily I have plenty of those but nevertheless it's good to know

Mufassa 01/10/2018
For my BLV MGN12 3D Printer mod for Anet A8. These do not come with a screw/bolt. A M5x15mm works good. Makes your Z-axis nice and tight.
T8 8mm Lead 2mm Pitch T Thread POM Trapezoidal Screw Nut Seat For 3D Printer
T8 8mm Lead 2mm Pitch T Thread POM Trapezoidal Screw Nut Seat For 3D Printer
US$2.15 US$7.99
0
Comments (1)

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe