Customer Reviews

4.84 out of 5
Write a Review
  • All Reviews (67)
  • Image (8)
  • Video (0)
  • All Star
    • All Star(67)
    • 5 Star(58)
    • 4 Star(8)
    • 3 Star(0)
    • 2 Star(1)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
|
Show Original

A part of the review has been auto-translated.

  • 24/02/2021

    Nice, and functional! I have to try it but it looks great!

    Comments
    Show Original
  • 20/01/2021

    Perfect for my Artillery X1. It's not like in the picture, but it's even better, since in the middle there are no letters. 10/10

    Comments
    Show Original
  • 09/02/2021

    Very good product. Fast shipping. Thank you BG

    Comments
    Show Original
  • 28/05/2020

    Good morning, To begin with, the article delivered may have a different appearance as was the case for mine but this does not affect its quality (See photo). The magnetic hook is excellent and does not really decrease despite an intensive heating of the tray (100°C for the ABS). No worries to take off a print a few minutes after it is finished. It remains to be seen the life of the surface during a relatively sustained use. Installation takes a few minutes (Maximum 10 minutes if this is the first time you install one) I also attached a video that I made to explain the installation of the said surface. You will also find that the procedure is extremely simple and fast. Just apply the right tips to ensure the best possible assembly. My video: https://www.youtube.com/watch?v=G1qdH5PAUzs I hope you find this useful. It's a must have for his printer so don't hesitate.

    Comments
    Show Original
  • 10/01/2020

    is small for cr10s pro

    Comments
    Show Original
  • 04/05/2019

    Description says usable up to 80°, but in facts, only up to 70° like you could see on the pic. Can't be used for nylon or abs.

    Comments
    Show Original
  • 29/03/2019

    für 20x20 super aber nicht für 30x30

    Comments
    Show Original
  • 25/03/2019

    Why would you ship it in a bag with my pulleys and bearings?? There is a large dent in the middle of the surface from being squished into the pulleys. Then the edges have large dents, not to mention one side being folded over. I dont think I'll even use this now as my prints which always start in the center are not going to be flat. I am sure I would have given 5 stars had this been protected some what during shipping.

    Comments
    Show Original
  • 31/05/2021

    straight out of the packet prints stick super tight, almost too tight. after a couple weeks of printing they're sticking less but to a more appropriate amount. not sure if it will be too loose long term at this stage. cheap way to get a removable print bed which is super useful, although I did already crack part of the surface under normal use

    Comments
    Show Original
  • 21/01/2021

    Very good quality and it adheres much better than glass or similar. PETG adheres well at 60C and there are no residues. The plate is excellent, 100% recommended.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • AU$25.41
    • AU$24.26
    • AU$550.20
    • AU$16.67
    • AU$56.11
    • AU$21.22
    • AU$16.67
    • AU$7.09
    • AU$9.09
    • AU$9.64
    • AU$351.63
    • AU$206.83
    • AU$11.02
    • AU$55.14
    • AU$179.25
    • AU$24.26
    • AU$2.98
    • AU$5.50