Customer Reviews

4.9 out of 5
See all 143 reviews
Write a Review
  • All Reviews (143)
  • Image (17)
  • Video (0)
  • All Star
    • All Star(143)
    • 5 Star(134)
    • 4 Star(6)
    • 3 Star(2)
    • 2 Star(0)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
|
Show Original

A part of the review has been auto-translated.

  • 01/02/2018

    The OSD doesn't flicker! First one that doesn't, yet. It flies tight but the PID's had to be higher than usual, 75 P and 72 I for pitch. That on a 220 qav only 501 grams. Still though, flies good. I like the connector for esc leads, makes it easy to pull it if u have 2. Clever as all the leads that need to stay on the craft are on the connector, add a JST for the receiver and video in/out and easy out. Came with Betaflight 3.2.1 running 4k gyro and acc loops. This one measured out at 7.2 g. If u solder leads right to the board no pin headers its 4-5 grams lighter than most F3 boards.

    Comments
    Show Original
  • 19/05/2018

    received this flight controller trying to figure out how to get the osd working, yes its wired in properly but am quite unsure as to weather i have to use the +vbat off the plug to get the data through the osd? Secondly is it possible to put +vbat into this as its description says it only takes up to 5..5v ? Can someone help me with sorting this out or does the osd work but not show any data?... help much appreciated Thanks

    Comments
    Show Original
  • 06/12/2017

    Very good and stable FC with OSD and Sd card functions. Sbus works on rx6. Must soft mount it to reduce vibrations,

    Comments (1)
    Show Original
  • 24/08/2019

    from mumbai,india. I got v2 delivered I dont know why.. but its looking nice I will be updating soon

    Comments
    Show Original
  • 02/01/2018

    FC works great I will buy another wiring was easy straight forward j like it so far

    Comments (3)
    Show Original
  • 09/01/2020

    Is working

    Comments
    Show Original
  • 27/12/2017

    The plasticity of this board is great. you can solder each of your motor ESC signal wires to individual pads or use a single ribbon cable. I opted to use the single ribbon cable approach with my signal wires vbat and current sensor all in one place. The motor signals worked great however vbat and current values do not work as they do not show up on osd.

    Comments (1)
    Show Original
  • 14/12/2017

    This clone works like the original. No issues. Has survived MultiGP race crashing.

    Comments
    Show Original
  • 23/07/2019

    ottimo

    Comments
    Show Original
  • 16/07/2019

    Awesome flight controller! Work with all the sensors i need. GPS, compass etc. Very stable and responsive! The image is if my 3D printen fpv drone.

    Comments (1)
    Show Original
Show:

    Total 0 pages

    Go to page

    Go
    recommendation for you
    • US$23.99
    • US$29.99
    • US$16.99
    • US$29.99
    • US$20.89
    • US$6.59
    • US$9.99
    • US$6.66
    • US$13.19
    • US$20.10
    • US$43.99
    • US$33.50
    • US$95.99
    • US$79.99
    • US$57.99
    • US$76.99
    • US$18.45
    • US$8.79