Customer Reviews

4.94 out of 5
See all 1142 reviews
Write a Review
  • All Reviews (1142)
  • Image (62)
  • Video (0)
  • All Star
    • All Star(1142)
    • 5 Star(1083)
    • 4 Star(51)
    • 3 Star(4)
    • 2 Star(1)
    • 1 Star(3)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
|
Show Original

A part of the review has been auto-translated.

  • 27/05/2020

    To start, the product fits and secures snugly in my 0xa tool post. The dovetails are well machined and polished, they even took extra time to chamfer the 90° edges and corners that could be uncomfortable when holding it & tightening a tool piece into the holder. ( Nice Job ) I tossed in a comparison piece and covered the brand name because its not important. You will notice the much more expensive 250-001 tool holder (blue tape) did not take the time to chamfer edges and inside the Dado where your tooling will rest the back is not polished and left ruff. They did however also paint/anodize the inside of the Dado. Personally I like the polished metal over more anodizing it does leave more surface exposed and possible damage can take place if you don't take care of the bare surfaces. That part will be a personal preference. Now for a couple small dislikes. The depth from front to back on the more expensive tool holder is 19.98mm the new units are 19.22 it is small but was noticeable without even measuring. I am not sure if the 0.76mm will effect the over all rigidness, or maybe lead to bending dovetails later down the road. I really hope not and would reach out to the manufacturer if an issue came up. The second issue is with the Bottom shelf of the Dado. My original Tool holder has a shelf thickness of 4mm. and the new units have a shelf thickness of 3.82. yes it is small 0.18mm. and this being one of the thinner portions of the tool holder I really wood have liked to see that at full thickness 4mm. Time will tell as I am a chronic over tightener, if the shelf will bend as I tighten the tooling secure screws, or if vibration or chatter over time will weak it to a failing point. The cost was great they arrived early, slightly under packaged for any type of impact damage that could take place in my opinion but they were well oiled and protected from moisture threats.

    Comments
    Show Original
  • 11/12/2020

    This is a quality toolpost and one I am very please with so far. The tools are of a quality construction and the post holds things rock-steady. It does not fit the Myford ML10's stud by default as this is slightly larger than the M10 but a new stud can be purchased from a UK store online, but the base needs to ne turned down in depth by about 1.4mm as it's designed for the ML7. The holders are great quality and while I felt the adjustment screw was fiddly it does the job. my only regret now is not buying more holders 😂 Top job Machifit and I hope you produce a sine bar now, maybe a more extensive range of gauge blocks too!

    Comments (3)
    Show Original
  • 21/03/2021

    Good!

    Comments (1)
    Show Original
  • 01/12/2020

    I must admit, I am pleasantly surprised at how good the quality is on this tool post, it's definitely gibs style and not piston, it's solid and the movent is almost buttery smooth! I now regret not buying the tool holders at the same time and want to install it on my lathe IMMEDIATELY!, but have no tool holder that will work with it! I need to use it NOW! :-D Definitely great value for the money. gonna buy the entire set, a few times 😇

    Comments
    Show Original
  • 25/09/2020

    all items purchased are of excellent quality at a truly competitive price. I am really happy with the purchase. Shipping and receiving in record time. Congratulations to the seller. Thank you

    Comments
    Show Original
  • 26/02/2020

    Okay

    Comments
    Show Original
  • 26/10/2019

    Not packed enough.

    Comments
    Show Original
  • 12/01/2021

    Fully satisfied! Item as described, indispensable to mount 10x10 tools on my little Myford ML7.

    Comments
    Show Original
  • 06/08/2020

    Suitable for my C1 lathe, nicely ground finish on mating faces, no sharp edges or burs.

    Comments
    Show Original
  • 20/05/2020

    Super grip for a hobby lathe. It works great, it's precise, it doesn't jam. The lathe knife frames are easily adjustable. I fitted it on my little lathe (Sig C6 clone) after a slight modification of the support. Recommend.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$28.99
    • US$6.59
    • US$22.14
    • US$11.36
    • US$57.19
    • US$30.93
    • US$68.19
    • US$13.19
    • US$75.99
    • US$24.43
    • US$122.09
    • US$10.99
    • US$7.63
    • US$16.63
    • US$12.83
    • US$16.99
    • US$7.99
    • US$69.99