At Banggood, we uses cookies and other similar technologies to provide you with essential functionalities and for aggregated statistics.
We also use optional cookies for a better experience with:
You can choose not to allow some types of cookies via"Cookie Settings".If you want to learn more about it, you can swipe to the bottom of the page to see the Privacy Policy
When you visit any website, it may store or retrieve information on your browser, mostly in the form of cookies. This information might be about you, your preferences or your device and is mostly used to make the site work as you expect it to. The information does not usually directly identify you, but it can give you a more personalized web experience.
Because we respect your right to privacy, you can choose not to allow some types of cookies. However, blocking some types of cookies may impact your experience of the site and the services we are able to offer.
{{$productInfo.reviewAmount.average}} out of 5
Notice:
Add new UART ELRS 2.4G Receiver Version.
It comes with a new X12 ELRS Pro v1.1 flight controller, onboard vtx and onboard uart elrs receiver are controlled by ESP32 chip , now you have a free set of UART and you can flash single ExpressLRS firmware for the Mobula8 ELRS .
Flight Controller | X12 ELRS Pro v1.1 AIO 5-IN-1 Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH) ,ESP32-PICO-D4 |
Onboard 4in1 ESC | Power supply: 1-2S LiPo/LiPo HV Current: 12A continuous peak 15A (3 seconds) Support BLHeliSuite programmable Firmware target: Z_H_30 Default protocol: DSHOT300 Bluejay firmware ready |
Onboard uart ExpressLRS 2.4GHz Receiver | Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V3.0 RF Frequency: 2.4GHz Antenna : SMD antenna Telemetry output Power: <12dBm Receiver protocol: Serial_based CRSF Compatible with ExpressLRS V3.x.x TX Module Could flash single ELRS receiver firmware by Wifi ExpressLRS firmware target: Generic ESP32 2.4Ghz Rx and VTx |
Onboard 5.8g OPENVTX | Firmware version: OPENVTX Smartaudio v2.1 PIT Mode support RCE Mode support Channels:48ch Transmitting Power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v): <650ma (400mw) |
Features:
X12 ELRS Pro v1.1 5-IN-1 AIO flight controller built-in 2.4G ELRS V3.0 and OPENVTX
VTX Power up to 400mw
ELRS V3.0 (Default), could flash elrs firmware for the receiver by wifi
EX1103 KV110000 motors
CaddxFPV Ant FPV camera
Smooth and powerful
Compatible for 1S-2S Lipo/LIHV battery
Recommend 2S 450mah/550mah/650mah battery (Not include)
Specifications: ( Manual for UART ELRS / ELRS / Frsky / PNP or TBS version ) Brand Name: Happymodel Item Name: Mobula8 1-2S 85mm Micro FPV whoop drone Wheelbase: 85mm Size: 120mm*120mm*50mm Weight: 43g Receiver option: 2.4G ELRS SPI(Support ELRS v2.0, provide firmware could compatible with elrs v3.0) SPI Frsky D8/D16 not compatible with EMAX E6 radio SPI Flysky AFHDS2A PNP (without onboard receiver) TBS version(with external TBS CRSF NANO RX)
EX1103 KV11000 brushless motor | Mode: EX1103 KV11000 |
Gemfan Hurricane 2023 tri-blade propellers(4cw+4ccw) | Weight:0.88g |
X12 5-IN-1 AIO flight controller | X12 ELRS V2.1 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280 |
Onboard 4in1 ESC | Power supply: 1-2S LiPo/LiPo HV Default protocol: DSHOT300 |
Onboard SPI ExpressLRS 2.4GHz Receiver | Packet Rate option: 50Hz/150Hz/250Hz/500Hz |
Onboard SPI Frsky D8/D16 receiver Versio | SPI BUS receiver Frsky D8/D16 compatible |
Onboard SPI Flysky receiver Version | SPI BUS receiver |
PNP Version | Full UART1 for external Receiver |
External TBS CRSF Nano receiver version | Original TBS Receiver ,CRSF Protocol , Official TBS transmitter compatible |
Onboard 5.8g OPENVTX | Firmware version: OPENVTX |
Caddx ANT 1200tvl camera | Image Sensor: 1/3″ CMOS Sensor Lens: 1.8mm |
Package Included:
1* Happymodel Mobula8 RC Drone
Shipping method(s) | Shipping time | Tracking information |
---|