A part of the review has been auto-translated.
Works great, as advertised. Less sticky with PETG, which is what I wanted. Achieved better print quality with this. I DO RECOMMEND IT!
Actually not sure why my review for the 5pcs was not published (sent on 22/07/2021), so I will try again for the 2pcs which I had ordered separately.
In general quality is good, Nozzle fits well on MK8 hot end (CR10-V2 in my case) and print quality was also fine (printed approx. 2kg filamen with that nozzle so far)
BUT: This is NOT a 0.4mm nozzle. I found out the hard way, when I had to clean the nozzle and my 0.4mm needle (wich I had used successfully on multiple other 0.4mm nozzles before) did not fit into this nozzle. I had to use 0.35mm
For that reason I gave only 3 stars in my first review, will try with 4 stars now. Atually the only problem is the hole, which is way to small. But that isn't a problem as long as you choose line width somewere between 0.36 and 0.45 mm. I sometimes print at 125% line width (i.e. 0.5mm) or even 150% line width (i.e. 0.6mm) for faster (and even stronger !) prints. In this case slopes on the inside are no longer printed properly with this nozzle, because the thinner filament string doesn't stick well to the "neighbour".
Actually not sure why my review for the 5pcs was not published (sent on 22/07/2021), so I will try again for the 2pcs which I had ordered separately.
In general quality is good, Nozzle fits well on MK8 hot end (CR10-V2 in my case) and print quality was also fine (printed approx. 2kg filamen with that nozzle so far)
BUT: This is NOT a 0.4mm nozzle. I found out the hard way, when I had to clean the nozzle and my 0.4mm needle (wich I had used successfully on multiple other 0.4mm nozzles before) did not fit into this nozzle. I had to use 0.35mm
For that reason I gave only 3 stars in my first review, will try with 4 stars now. Atually the only problem is the hole, which is way to small. But that isn't a problem as long as you choose line width somewere between 0.36 and 0.45 mm. I sometimes print at 125% line width (i.e. 0.5mm) or even 150% line width (i.e. 0.6mm) for faster (and even stronger !) prints. In this case slopes on the inside are no longer printed properly with this nozzle, because the thinner filament string doesn't stick well to the "neighbour".
Actually not sure why my review for the 5pcs was not published (sent on 22/07/2021), so I will try again for the 2pcs which I had ordered separately.
In general quality is good, Nozzle fits well on MK8 hot end (CR10-V2 in my case) and print quality was also fine (printed approx. 2kg filamen with that nozzle so far)
BUT: This is NOT a 0.4mm nozzle. I found out the hard way, when I had to clean the nozzle and my 0.4mm needle (wich I had used successfully on multiple other 0.4mm nozzles before) did not fit into this nozzle. I had to use 0.35mm
For that reason I gave only 3 stars in my first review, will try with 4 stars now. Atually the only problem is the hole, which is way to small. But that isn't a problem as long as you choose line width somewere between 0.36 and 0.45 mm. I sometimes print at 125% line width (i.e. 0.5mm) or even 150% line width (i.e. 0.6mm) for faster (and even stronger !) prints. In this case slopes on the inside are no longer printed properly with this nozzle, because the thinner filament string doesn't stick well to the "neighbour".