Customer Reviews

4.95 out of 5
See all 264 reviews
Write a Review
  • All Reviews (264)
  • Image (47)
  • Video (1)
  • All Star
    • All Star(264)
    • 5 Star(253)
    • 4 Star(9)
    • 3 Star(2)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
|
Show Original

A part of the review has been auto-translated.

  • 04/05/2018

    Since the control board was changed there is no need for the hole in the front panel for the calibration potentiometer so I changed the position of the LED to use the hole for that. I fitted the front panel backwards to hide all the branding and lettering, I think its better with a cleaner look. I also cut and shaped 2 pieces of tinted perspex as windows for the digital display and the heating indicator LED, it tames the very bright LEDs of the display a little.

    Comments
    Show Original
  • 20/02/2018

    Contra: power switch, only single pole, no good for a metal case, 4 points for appearance! Neutral: front plate for LED version only, no plate for OLED type Pro: excellent fabrication quality, very low gaps, very good anodizing! I changed the power switch for a two pole illuminated one and worked a new front from black acryl. Together with the STC controller (from BG) and a cheap supply lying around here i got a very comfortable and absolutely well working soldering station! Its DIY, if holes are needed for fitting the chosen supply, drill them and cut threads.

    Comments
    Show Original
  • 29/11/2017

    Ich habe das Metallgehäuse bestellt, weil ich es schöner als das Plastikgehäuse für den Bau einer Lötstation finde. Was ich leider nicht bedacht habe, im Innern des Gehäuse sind keine Befestigungspunkte zum Befestigen des Netzteils. Das in der Beschreibung über dem Zusammenbau der Lötstation gezeigte Netzteil, konnte ich leider nicht finden, also habe das Netzteil "Geekcreit® 4A bis 6A 24V Schalter Energieversorgung Board AC-DC Power Modul" gewählt. Dieses habe ich dann mit seitlichen Halterungen im Gehäuse fixiert. Beim Einbau der Regeleinheit hat die Anzeige nicht ganz gepasst und ich habe das Loch für die Temperaturregelung etwas vergrössern müssen.

    Comments
    Show Original
  • 24/08/2017

    Простая и прочная конструкция. Поскольку в регуляторе используется импульсный преобразователь, рекомендую для лучшего экранирования использовать именно этот корпус, а не пластиковый (тоже предлагаемый на BG).

    Comments
    Show Original
  • 31/10/2017

    Отличный корпус , всё в наличии, только лицевую панель немножко пришлось доработать напильником. Подставка для паяльника куплена отдельно.

    Comments (1)
    Show Original
  • 31/10/2017

    С чем я столкнулся при сборке. 1: Сетевой кабель 2: Нет крепления для платы (блока питания). 3: Переднюю панель пришлось подгонять под плату.

    Comments
    Show Original
  • 25/05/2017

    The housing is made of black anodised aluminum with drilled panels for temperature controller, 220V power socket and switch. It comes with the necessary screws and the panels are inscribed. A quality product.

    Comments
    Show Original
  • 14/04/2017

    Great case for T12 soldering station (http://www.banggood.com/Digital-Soldering-Iron-Station-Temperature-Controller-Kits-for-HAKKO-T12-Handle-p-993248.html?p=W024148132309201612B) If you need power supply this one fits great inside: http://www.banggood.com/4A-To-6A-24V-Switching-Power-Supply-Board-AC-DC-Power-Module-p-969204.html?p=W024148132309201612B

    Comments
    Show Original
  • 02/09/2017

    I mount the solder station box with Power supply board "Geekcreit" inside. Need to use two pieces of the glass fiber board to mount power supply. After mounting i close the box and all is ready.

    Comments
    Show Original
  • 16/11/2018

    Looks great, Need to file about 1mm to the right of the temperature control encoder hole (on the front panel) for a perfect fit if used with DIY T12 kit ID: 1146578; otherwise you risk damaging the PCB when trying to fit the front panel, either the PCB will bend or the aviation connector won't fit straight For installing a power supply module like ID: 969204, you need to insulate the bottom of thw PCB with some electrical tape, or high temperature tape, I also added a piece of cardboard on the underside for extra measure You can attach a power supply inside with double sided tape if you don't wish to drill mounting holes Picture is of assembled T12 station

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • AU$16.80
    • AU$9.14
    • AU$5.92
    • AU$7.61
    • AU$15.24
    • AU$7.61
    • AU$21.97
    • AU$12.46
    • AU$19.81
    • AU$12.19
    • AU$13.71
    • AU$6.27
    • AU$19.39
    • AU$8.78
    • AU$8.30
    • AU$19.45
    • AU$9.97
    • AU$54.88