Customer Reviews

4.88 out of 5
See all 24 reviews
Write a Review
  • All Reviews (24)
  • Image (2)
  • Video (0)
  • All Star
    • All Star(24)
    • 5 Star(22)
    • 4 Star(1)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
|
Show Original

A part of the review has been auto-translated.

  • 04/10/2018

    Could come in English version with proper instructions. You need to do some research to understand where and how to solder some of the more complex components. The PCB is lowish quality - honesty the only thing that really needs to be improved.

    Comments
    Show Original
  • 30/04/2019

    Assembled and working. Good sensitivity, pulls in lots of stations.

    Comments
    Show Original
  • 29/04/2021

    The product case is so-so, there are small scratches in the case, but nothing fatal. All of the components are there. Waiting in the line for soldering.

    Comments
    Show Original
  • 12/07/2021

    All right, I liked the stuff

    Comments
    Show Original
  • 04/07/2021

    Excellent radio kit. Easy to solder and relative good sensitivity

    Comments
    Show Original
  • 06/05/2021

    top !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    Comments
    Show Original
  • 04/04/2018

    This is a very good little kit if you have built transistor radios before. The instruction are in Chinese. But can be deciphered. It's only the colors of the I.F. transformers which are not very clear. but hay, guess what, I learned some Chinese. I just checked the Chinese symbols out for the colors on the web. The kit was very complete and once assembled and tweaked a bit (I.F.'s) (don't press too hard on them), It worked well. I used a digital meter on the ohms range to read the values of the resisters which are in English on the instruction sheet. Very Cheap to buy and the quality of the parts was outstanding Overall 8/10!

    Comments
    Show Original
  • 11/02/2018

    I found this am radio very easy to put together and quality very good for what it is as i aligned IF coils via a 455 khz alignment oscillator with no problems and it pulls in all stations in my area . Please note if you are a beginner take note that on the pcb you will see 4 small breaks in the tracks of each of the IF coils and they are marked A/B/C/D these are the test points to measure milli amps in each of the operating stages of this radio if each measurement is within the specs of the schematic supplied do not forget to connect each one with a bridge of solder or else your radio will not work .

    Comments
    Show Original
  • 06/08/2020

    First, the good: it is a really neat project to do with your kids. Thank you for the product! Now, what can be improved in no particular order. Note that these are just minor annoyances, not something against the product: 1. The board is too small -- it cuts through C1 holes and makes soldering C1 harder than the rest. Some other commenters mentioned this as well 2. It would have been nice to help identify magnetic rod coil leads (1, 2, 3 and 4) 3. Speaker came a little damaged 4. The case is too small! I shoehorned 2x Energizer AA batteries but they were pressing very hard against the speaker's magnet, and they were really distorting case plastic 5. Few spares (223 capacitors) would be nice

    Comments
    Show Original
  • 02/08/2018

    nice project for my grand daughter. I did notice that the pcb was cut too close to the edge causing one thru hole to be split open for c1 capacitor . Reading the other replies I see that somebody else had the same problem

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • AU$17.24
    • AU$31.37
    • AU$27.07
    • AU$39.48
    • AU$18.52
    • AU$16.57
    • AU$29.37
    • AU$12.82
    • AU$14.24
    • AU$8.54
    • AU$10.46
    • AU$24.22
    • AU$8.97
    • AU$17.24
    • AU$33.86
    • AU$8.83
    • AU$11.39
    • AU$5.69