Customer Reviews

5 out of 5
Write a Review
  • All Reviews (20)
  • Image (10)
  • Video (0)
  • All Star
    • All Star(20)
    • 5 Star(20)
    • 4 Star(0)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
|
Show Original

A part of the review has been auto-translated.

  • 22/10/2020

    It's a very high quality frame First you open the box and you'll see a lot of parts and screws The screws are packaged by size and up to size representation Carbon parts are cut cleanly and DIATONE on the upper plate.The bottom plate is vacuum-packed with Roma lettering The screw heads are specially and cleanly chamfered, and even the motor mounting screws are provided with the same thing The accuracy of the screw holes is high and the screws are dropped slightly The stack hole is set to 20x20 30.5x30.5 (with seat) in the center, and 20x20 (with seat) in the rear are set to be shifted back and forth in three stages The camera mounts are 19 and 20mm by changing the left and right sides Antenna mount supports VTX antennas, 2.4G and CrossFire antennas The standoff height is a little tight, 23mm Board of RunCam hybrid4K with isolated plates in ESC and FC size conversion of 30.5X30.5 to center CAP(x2) insulated plate VTX insulated plate in the rear insulated plate receiver configuration Others Top plate front tip GPS behind 4S/1800mAh Stand up the VTX antenna and receiver antenna by using other mounts instead of using the supplied antenna mount (^-^) It's still in the tentative stage, but I'm very satisfied with it (^-^) I won't miss buying it! It's cheap, but it's a very recommended frame! It comes with a camera mount that doesn't seem to work (laughs)

    Comments (1)
    Show Original
  • 15/01/2021

    Really nice frame, one of the most beautiful 5'' frames. Every part is high end quality, every screw, frame part, plastic parts look so premium. You get assembly diagram and in 30 mins you will assemble it. You will also get a lot of spare and additional parts like screws and gaskets. Fast delivery and 5 stars product

    Comments
    Show Original
  • 11/02/2021

    STDver will be the third (^-^) Cheap and strong on my favorite aircraft. Highly recommended frame (^-^) The DJIver and STDver each fly with RunCam hybrid4K and GPS, T-motor's Blackbird V2 and BMS Raptor, but the high-pitch prop is over 180km/h high power aircraft It's an overspec for a beginner amateur, and I think I punched out a bit during the trick, but I'm flying to a hell of a place I'm thrilled when I fly between structures and trees Just because I'm nervous about drifting stones, I built the Choi-flying aircraft that can fly comfortably This frame is surprisingly light, 2205/2300kv, and even older non-force motors fly well (^-^) The sturdy makes it perfect for training choy flyers I'm going to make a spare machine for the Choi aircraft and I'm going to purchase additional items For 2205, 35A of FCinESC is enough If you're flying Choi, the VTX is also cheap about $15-20 and 200-400mW is fine (^-^) With this frame, you can build a low-cost, good-looking aircraft that can fly comfortably and well (^-^) We can handle both low-cost and high-spec machines I can recommend it. It's a great frame (^-^)

    Comments
    Show Original
  • 10/02/2021

    STD is the second, and the third with DJIver The first aircraft was a RunCam hybrid4K and GPS-equipped aircraft The stack space is a little low, and it's hard to layer That's enough Since it's a Freestyle machine, there's stack space on the back of the fuselage There's also some space behind the camera The frame is very clean, there are many spare parts, screws, etc., and I think it's the best cost performance The second DJIver. This frame is similar to the STDVer, but most parts are designed specifically There are three stack spaces behind the camera, the center, and the back, the height is the same as STDver RunCam Turn the hybrid4K GPS 2307 at 4S/3000mAh I'm flying on CrossFire, but I'm overspecified for a novice amateur The camera cage is strong and the timing was slow when I made it soaring, but the camera and the aircraft were safe w Sturdy, well built and cheap for about $50 I thought that this frame would be good even for the aircraft for flying with a powerless motor...I built the third aircraft(^-^) It's a surprisingly light frame and flies well even at 2205/2300 kv Ordered a fourth plane to make a spare plane to fly Choi and wait for arrival(^-^) The GPS (180) is placed near the camera and the 4S/1800mAh is right behind it

    Comments
    Show Original
  • 31/12/2020

    Everything from the screws to the carbon fiber and packaging is really high quality. All the pieces fit together perfectly and building this frame was a breeze, especially compared to some knock-off crappy frames I have bought before! Would highly recommend!

    Comments
    Show Original
  • 26/04/2021

    In accordance with the description received in a Diatone box, in a bag without too much protection, waiting to mount it to check the conformity of the Frame and test it in flight.

    Comments
    Show Original
  • 09/03/2021

    really nice frame thin arms but other then that i love it

    Comments
    Show Original
  • 09/02/2021

    Everything is excellent! quality as always at the height

    Comments
    Show Original
  • 05/04/2021

    i cahnge with mamba stack

    Comments
    Show Original
  • deeVIP4
    DE
    29/01/2021

    a hammer frame, bought two of them directly

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • AU$88.38
    • AU$17.94
    • AU$4.13
    • AU$23.51
    • AU$9.65
    • AU$3.43
    • AU$14.99
    • AU$13.25
    • AU$4.13
    • AU$174.03