Customer Reviews

4.96 out of 5
Write a Review
  • All Reviews (554)
  • Image (56)
  • Video (0)
  • All Star
    • All Star(554)
    • 5 Star(532)
    • 4 Star(21)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
|
Show Original

A part of the review has been auto-translated.

  • 29/05/2021

    Excellent packaging, except from a little dent on the side the box sustained no damage at all during transit. Everything is packed in a very sturdy box. All the items are protected inside the box by a tailor sized foam inlay. Very very good indeed, packaging leaves nothing to be desired at all. (I wish more products where packed this way, would save a great deal of frustration caused by items getting damaged or broken during transport.) This attention to detail installs confidence in the product as well. I have read many good things about this sensor (it is version 3.1) and hope it performs well for me too. There are many video's out there explaining installation of this sensor on various mainboards so I do not expect any problem. Hopefully this brings me a step closer to that "perfect first layer".

    Comments
    Show Original
  • 24/08/2020

    This works great! No more spinning the wheels over and over again to level my bed before 3-D printing. The install is a little bit tricky but there are lots of online instructions and videos to help you. highly recommended.

    Comments
    Show Original
  • 17/07/2020

    Works a charm. Requires a little work to set up, but following instructions its all fairly straightforward. Instructions are not great, but there are plenty of excellent videos online (I suggest the "Teaching Tech" channel). It is very easy to accidentally insert one of the connectors incorrectly (one column of pins over). I did this and had issues, thought it was the firmware upload and went through various firmware revisions before finding the mistake. I downloaded the latest firmware and set up according to online instructions. Now my first layer goes down a treat *every single time* without the need to check the bed levelling manually with paper. I cannot recommend this product more strongly - I'm kicking myself for not ordering the printer with this option pre-installed. If you don't have an automatic bed leveller - this is the number one upgrade to buy before anything else.

    Comments
    Show Original
  • GDLVIP3
    BG
    13/04/2021

    The box was damaged, but thankfully the content was intact. Very, should I say extremely long delivery period ( and that coming from the UK ). Not tested yet.

    Comments
    Show Original
  • 14/09/2020

    This product arrived within 2 weeks of ordering it. For international delivery I am very impressed. The item itself is really well packaged. It is complete, and appears to be of good quality. My printer is currently mid print so I have not had a chance to install it, but as this is a genuine item I have no doubts it will function perfectly.

    Comments
    Show Original
  • 03/07/2020

    Got BL Touch V1.3 for Creality V1 mainboard. It is relatively easy to install (Ender 3), once installed and enabled in the firmware it works as expected. The only drawback of this solution is that the Pinboard A (pin expansion for BL Touch) does not really fit into the mainboard enclosure when connected to all the cables as it is too high and conflicts with the fan. It is also worth to remember to add auto-leveling commands to the slicer output code.

    Comments
    Show Original
  • 27/03/2021

    Reception within 10/12 days. Excellent product! Relatively simple installation (unless like me there is glue to remove from the connectors of the motherboard), firmware update, offset adjustment and addition of the G29 in the slicer (Cura for example). Now that everything is good, I finally have a correct levelling of the bed all over the surface!

    Comments
    Show Original
  • 13/02/2021

    was a challenge but got there in the end. fits ender 3 v2 but has an adapter which attached to the LCD ribbon cable port - make sure you follow the wiring diagram and cant go wrong. make sure red cable is to VCC as per diagram.

    Comments (2)
    Show Original
  • 10/01/2021

    Semma product buyed from Tamilnadu, chennai. It tooks 2months to arrive in corona period.

    Comments
    Show Original
  • 08/03/2021

    Worked fine. The ISPUSB cable was really handy to install the new firmware and all the necessary screws were included as well. The process was easy to follow and now is even possible to install other firmware's. The BLTouch is a original one, not a parallel and even came with the zip ties and a extra probe. All in all a very good deal and great improvement for your printer.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • AU$23.68
    • AU$23.68
    • AU$59.65
    • AU$277.36
    • AU$558.74
    • AU$20.72
    • AU$67.19
    • AU$5.53
    • AU$13.32
    • AU$17.49
    • AU$201.95
    • AU$348.72
    • AU$53.84
    • AU$14.80
    • AU$39.03
    • AU$17.84
    • AU$14.06
    • AU$10.03