Customer Reviews

4.95 out of 5
Write a Review
  • All Reviews (76)
  • Image (7)
  • Video (0)
  • All Star
    • All Star(76)
    • 5 Star(74)
    • 4 Star(1)
    • 3 Star(0)
    • 2 Star(1)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
  • November-05 2020 04:11:35

    The display is very nice. Works very nicely with the Mini E3 V2,0 board. The emulation mode is nice and the ability to easily switch to the touch screen by holding down the knob for 3 seconds is very useful. One thing to note is that the touch screen runs as a small computer feeding gcode to the mini , so if you want to print from the slot on the mini you need to be in emulation mode to view the files on the card. The touch screen interface can only access the files on the plug in USB stick or its

    Comments (1)
  • June-12 2020 12:03:36

    Bem embalado e em condições.. Só falta mesmo instalar para verificar se está tudo ok👌

    Comments
  • August-07 2020 04:45:04

    perfect as usual for this brand.

    Comments
  • December-17 2020 13:09:59

    Fajna sprawa. tylko dostawa 30 dni

    Comments
  • August-07 2020 08:24:21

    par contre il faut mettre la carte sous l’écran après car elle n’est plus repérée sur la carte mère

    Comments
  • December-10 2020 15:59:44

    Muito bom chegou rápido e tudo certinho, recomendo.

    Comments
  • July-17 2020 14:11:55

    great quality!

    Comments
  • October-21 2020 09:34:08

    fitted but found screen locked up on the two icons option turned out to be screen to much tight fit against metal frame cured by putting some washers inbetween board and ender plate which lifts away from the angled mounting plate hope this helps you guys firmware ok also braun rate sometimes wrong listing printer not connected but happy with purchase

    Comments
  • November-22 2020 04:51:48

    Working properly, az it was expected. I'm using it for Ender 3. Only the knob led isn't working, but I don't care, since it is doing what has to do. Before you build the screen into the metal case, where the original LCD was, use some Kapton tape for insulating the metal case from the touch screen, otherwise, you cannot use it. It feels like you continuously pressing the screen, therefore it is going back to the screen for selecting the simulator or touch screen. It is not described in the documentation. Anyway,

    Comments
  • September-21 2020 01:18:01

    Works really well on the Ender 3 Pro and SKR 1.3. Very customisable and colourful. You don't lose functionality using the touch screen, instead of the traditional Marlin screen. You can also change the colours of text when using the Marlin screens and the encoder wheel works so much better than the original one. Additionally, you can use the SD and USB slots to update and print.

    Comments
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • AU$28.77
    • AU$25.89
    • AU$10.06
    • AU$10.88
    • AU$9.41
    • AU$16.34
    • AU$18.73
    • AU$7.54
    • AU$7.18
    • AU$47.07
    • AU$52.26
    • AU$3.40
    • AU$9.60
    • AU$22.86
    • AU$14.90
    • AU$3.13
    • AU$13.38
    • AU$4.70