Customer Reviews

4.96 out of 5
See all 215 reviews
Write a Review
  • All Reviews (215)
  • Image (42)
  • Video (0)
  • All Star
    • All Star(215)
    • 5 Star(210)
    • 4 Star(4)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
|
Show Original

A part of the review has been auto-translated.

  • 13/02/2021

    I've another one on order. I destroyed this one with my shakes and crappy solder iron and as a beginner I found it tricky (after it was going so well) - especially around the battery + and G for the VTx, and the backside of the micro USB. (I just need more practice, and less coffee!) That's an Eachine Novice ii toothpick frame in pictures; I wrecked it's original FC too, when all I should have done was splice some wires for an easy fix! I had to use my chainsaws round file to make the GEPRC motor connectors fit the Eachine Novice ii frame. Hopefully I'll have another review in a few weeks with the one that's on order used on the completed build.

    Comments (1)
    Show Original
  • 29/09/2021

    The package arrived within two weeks. I put a burnt-out controller on TinyGo. Updated betaflight firmware, cli parameters downloaded from geprc. Had to suffer with blheli settings. persistently gave the program an error. In the end, I found the first chromium extension and inverted the 2 and 3 motor rotation. Everything flew!)

    Comments
    Show Original
  • 18/11/2021

    purchased as a replacement of a drone GepRc... all ok

    Comments
    Show Original
  • 21/04/2021

    Molto bene

    Comments
    Show Original
  • 11/06/2021

    seems fine

    Comments
    Show Original
  • 21/11/2019

    I bought 4 for these boards and they all work perfectly. The smallest one using a 2s lipos and 1103 8000kv motors (Emax Avan 2.5 tribade props) and the largest with 1404 3850kv motors with 4s lipo (HQ 3X3X3 props). I have gone through many packs and the GEPRC 12a AIO board is handling it like a champ. With these light setup I can get over 11 minutes of flight (cruising speed) with a 4s 520mah HV lipo. And if I push it hard I will get about 5min of flight.

    Comments (2)
    Show Original
  • 05/08/2019

    us direct shipping was fast, ordered it Saturday was in my mailbox by the next Friday. good quality aio board with pads labeled for easy identification of soldering points gonna grab some more of these for sure

    Comments (2)
    Show Original
  • 10/08/2019

    Great board for toothpick builds or replacement for mobular 7. Flysky receiver signal wire needs to be soldered onto the pad in diagram on the V1.1 board.

    Comments
    Show Original
  • 08/05/2020

    super product very similar to the original card with the difference ready that one can put a buzzer on the geprc. My beta 75x3s revie. super fast delivery from us

    Comments
    Show Original
  • 19/10/2019

    Use this board to replace Sailfly original crazybee board. Not easy to setup because the motor mount is facing down and the camera solder pads are at the back with micro USB connector, thus camera and vtx need to use longer wire. For Sailfly setup, need to mount the board upside down and change the orientation in betaflight. Nevertheless, it perform really well compare to the original crazybee board.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$26.12
    • US$8.69
    • US$63.51
    • US$181.50
    • US$43.99
    • US$74.99
    • US$37.39
    • US$21.70
    • US$19.60
    • US$54.79
    • US$9.59
    • US$69.99
    • US$15.15
    • US$6.99
    • US$20.67
    • US$26.59
    • US$9.89
    • US$94.80