Customer Reviews

4.93 out of 5
Write a Review
  • All Reviews (447)
  • Image (73)
  • Video (2)
  • All Star
    • All Star(447)
    • 5 Star(425)
    • 4 Star(18)
    • 3 Star(2)
    • 2 Star(0)
    • 1 Star(2)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Australia)
|
Show Original

A part of the review has been auto-translated.

  • 22/10/2020

    Very fast shipment and good quality. Many friends here have complained about the manual which is in Chinese. So I tried to translate the manual using online translation. Please check the photos. If it is not very clear, just take a screenshot and then zoom in to see better. Sorry for the low quality, but that's the best possible. Hope it is helpful

    Comments (2)
    Show Original
  • 15/12/2020

    Perodotto very simple to use. The single button on the front controls everything from power on to power selection. The cables of the tips are short,creating some hindrance in use. At home I only had 1mm strice and they were perfectly welded, if it had to weld even thicker strips, it deserves the upgrade to 5 stars.

    Comments (1)
    Show Original
  • 22/01/2021

    A pulse is the solder is done! Show. I bought a 10m roll. The instructions are completely Chinese but for me it was easy to understand the operation. Hold the button and it goes into ON. Green LEDs mark the charge, of the internal battery. Every 2-3 sec you hear a beep, at that time by current pulse then eye not to short circuit. While it beeps the LEDs turn red and only those of the chosen power level are turned on. After it is in On press 2 times the button to switch to the power choice. Each pressure increases from 1 to 4 The red LEDs that indicate the chosen power. Press the button 2 more times to return to pulse working mode. Press and hold the button to turn off. Nice purchase!

    Comments
    Show Original
  • 29/12/2020

    Arrived from within EU in 3+ weeks. Made some test welds and this device has a big punch already on level 2 of power. The leads are little short but managable; they are insulated with clear silicone tubing on the copper part! Arrived with manual in chinese only. I used the instructions in item description above and they are on spot. Arrived with 4m 0.1x8mm nickel strip.

    Comments
    Show Original
  • 02/03/2021

    Ordered to collect the destination money from China for the first time, ordered to wait until I forgot to think that I would not send it. Liked 😊

    Comments (3)
    Show Original
  • 09/01/2021

    I took it as an experiment. For the time being, I am satisfied with the result, the battery-tape connection is correct. I'm gonna push it two times to one point, so it's gonna hold it a little harder for the battery. Since it will work well, in many cases it is necessary to tear it off by force, sometimes the piece of the tape remains on the battery. The surface should be cleaned or it will not heal properly. I bought a USB-C. We'll find out how the battery will sustain the effect in the longer term. What's worth paying attention to is the charge. The battery has a stronger self-discharge, it is worth taking it out every 2 months to see if it is not dead. I didn't count the amount of soldering points, I pressed quite a lot of points when making a bottle cap, a 5 cell li-ion pack was connected in parallel.

    Comments
    Show Original
  • 18/09/2020

    Great, this point welder suits me very well for the use I make of it. It perfectly welds the nickel strips to the batteries. It is a very good value for money in view of other more expensive machines, especially for the use I will make of it. Very fast shipping thanks to the fdp banggood express.

    Comments
    Show Original
  • 29/09/2020

    works very well, turns on by holding the button for a few seconds and immediately indicates the state of charge green leds, double click you access the selection of power on 4 levels, (my tests I made on power 3 e1mm tape), double click confirms the power. You can also select the automatic mode, with it the device recognizes the contact of the two spikes with the nickel and sends impulsed.

    Comments
    Show Original
  • 17/09/2020

    Arrived quickly in UK from EU via DHL. As suggested it was down to 50% charge to help with longevity of battery included. Very easy to use even with Chinese instructions as on the rear of the device it has the options in simple instruction. Long press on, green lights show charge. Quick short press twice shows red for power settings. I used from 2 to 4 in my testing. Choose your power setting and quick press twice to set it. 1.5 second and contact settings both work on micro usb device and to use this. You need to turn on and short press for each setting and it will show green then 1.5 sec red and so on or just green which means it is in contact mode. As for welding I think it depends on which Nickel strip you use. Even on power 4 setting I could rip strip off with 6 welds easy. But using some more expensive strip I had to use pliers. You get what you pay for with Nickel or plated strip. I tried 0.2mm pure Nickel and it would not hold well at all even on power 4 setting but we already know that as it is only for hobby use and claims only 0.1-0.12mm. You may get away with 0.15mm if pure Nickel. Stay safe friends. Sincere regards, Scott. ✌️🙏✌️

    Comments (1)
    Show Original
  • 14/04/2021

    On Saturday, the GLS came in. She came dead. I had to reload. It works perfectly. I ran a Cr2032 battery right away. You can download the manual, but I watched the video. I used the points and came out to about 1000,-Kč.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • AU$20.67
    • AU$13.64
    • AU$9.90
    • AU$37.91
    • AU$9.82
    • AU$6.91
    • AU$66.73
    • AU$6.41
    • AU$282.40
    • AU$22.05
    • AU$11.32
    • AU$13.32
    • AU$42.73
    • AU$72.06
    • AU$37.22
    • AU$261.99
    • AU$9.09
    • AU$7.57